Custom 1987 Mazda B2200 Truck - S-2000 Mazdawg

Creative Styles 20-inch Rolla

Doug Large
Oct 1, 2009
Photographers: Doug Large
Danny Bianchi is one of the many mini-truckers who have put the East Coast on the map by taking a truck and doing the unthinkable. Danny officially did all he could to raise the bar for all those out there building a Mazda. Mind was put to metal in the buildup of this Mazda pickup and this creativity really shows. Danny used a little bit of his previous tuner knowledge and a lot of his custom ideas to build the super-clean show truck gracing these pages.
Starting with an '87 Mazda B2000 body with completely stock sheetmetal, Danny sat down to brainstorm with Hector Comucho, a close friend and fellow club member of Creative Styles NY. Knowing what already had to be done to keep up with times, Danny first performed the usual: shaved doors, gas door, taillights, and mirrors. Next, Danny and Hector body-dropped the cab 3-1/4 inches. Then the stock fenders were swapped out for a set of 4x4 fenders from a B2600i. The front bumper was swapped out for a Toyota 4Runner's chrome bumper and that was treated with a billet grille to match the full billet grille above. Inside the bed, Danny installed a set of custom wheeltubs and installed a fuel cell. After Kenish finished all of the bodywork, the truck was sent to Danny's buddy Richie, where he sprayed the truck PPG Lazer Red.
Inside the truck, Danny had his close friend Russ build custom sheetmetal door panels as well as a sheetmetal dash, both of which where painted to match the exterior of the truck and given tweed accents. Danny sits comfortably in his Mazda courtesy of Honda S2000 leather seats. The steering wheel was swapped out and replaced with a custom chrome smiley face. Under the noticeable features of the truck sits a custom-built frame from the motor back consisting of a dropped frame clip in the rear so that the bed did not have to be body-dropped. The frame is made from 14 feet of 2/3-inch box tubing. Mike Janson and Danny performed all of the modifications to the frame. The rearend in Danny's Mazda is out of a 1988 Toyota Pickup truck. Danny's Mazda features a custom CCE Hydraulic setup using a custom two-bar kit and a custom rear shock setup. All this allows Danny's Mazda to tuck the 20-inch Neeper Titans.
Under the hood sits a powerhouse 2001 Honda S2000 motor. (Figure that one out.) To get this motor to work, Danny had to have a custom driveshaft built. The motor features a polished intake manifold, chrome-dipped valve covers, and a custom stainless steel header continuing on to a custom-built exhaust. An S2000 transmission was also swapped over. Danny would like to thank all of the people who made the buildup of his truck possible: High Performance Imports (HPI), Creative Styles, and The Drop Shop.
Photo 8/8   |   custom 1987 Mazda B2200 front Drivers Side View Burnout
The Lowdown

Rolling Attire
Wheels: 20-inch Neeper Titans
Tires: Nitto NT 555

Chassis Modifications
Suspension type: CCE hydraulics
Front suspension: Hydraulic cylinders
Rear suspension: Custom hydraulic setup
Spindles: Belltech drop spindles
Frame mods: Back-halved
Frame material: 2/3-inch box tubing
Gas tank: 12-gallon aluminum fuel cell
Brakes: Hard line
Performed by: Mike Janson and owner

Body Modifications
Shaved: Door handles, taillights, antenna, fuel door
Frenched: Taillights
Body dropped: 3-1/4 inches
Front end: Four-wheel-drive fenders, full billet grille, 4Runner bumper
Back end: Tailgate skin, custom taillights, roll pan, 1988 Toyota pickup wheel flares
Performed by: Kenesh, Hector, and owner

Brand and Colors: PPG Lazor Red
Performed by: Richie
City/state: Medford, New York

Seats: S2000 red and black leather seats
Dash: Custom-built and wrapped in tweed
Door panels: Custom-built
Center console: Custom-built
Headliner: Wrapped in tweed
Misc: Custom chrome smiley steering wheel
Performed by: Luis and Russ

Model/year: 2001 Honda S2000 motor # Of Cylinders: 4
Camshaft: Skunk2
Header/exhaust: Custom chrome
Driveshaft: Custom-built
Rearend type: '88 Toyota
Battery: Optima
Detail work: Chrome-dipped valve covers, polished intake manifold

Special Thanks
High Performance Imports Motorsports (HPI), Creative Styles, The Drop Shop, Doug Large, and everybody who helped along the way



Nissan Titan XD Walkaround

Subscribe Today and Save up to 83%!

Subscribe Truck Trend Magazine

Subscribe to:

Truck Trend

Subscribe Diesel Power Magazine

Subscribe to:

Diesel Power

Subscribe Truckin Magazine

Subscribe to: