Subscribe to the Free

Custom 1983 Chevrolet C10 - Bloodwork

Born Into A Family Of Motorheads, It's No Wonder Gabe Sandoval Built This '83 Chevy

Kevin Aguilar
Aug 1, 2007
Photographers: Kevin Aguilar
Photo 2/12   |   "I really wanted to build the motor, but my brother Simon insisted on doing it, and he even put in the crankshaft from a Corvette our dad raced in the early '70s." -Gabe Sandoval
The Sandovals can be described as a family of motorheads who have gasoline in their veins and who are consumed by the need to wrench on their rides. With a father well into drag racing and mud racing, Gabe and his older brother, Simon, were exposed to raw-powered vehicles at a young age. When Simon was old enough to drive, he bought a little Toyota Pickup and transformed it into a stylish mini-truck, which then inspired Gabe to toy around with a couple trucks, as well. Later, Gabe bought a Quad Cab Dodge Dakota to be customized. The Dodge had a 4.7L V-8 under the hood, a custom airbag suspension by Ekstensive Metalworks, and a flamed paintjob by Pat Maxwell. After driving it for a while, the Dakota quickly became old news and motivated Gabe to build a truck with his own two hands.
Gabe knew that tearing down a truck and building it from the frame up would be like an instinct to him. The talent was in Gabe's blood, and all he needed was to get his hands on an inexpensive truck that could be built with the proper work. While at his friend's shop, he spotted this '83 Chevy pickup sitting in the parking lot. It was everything Gabe was looking for and was just waiting to be worked on. His friend really wanted to build it but was too busy to do so. Gabe bugged him about selling the truck, and his friend finally gave in and let him snatch it for a measly $1,000.
Once the truck was at Gabe's home garage, he was able to assess its damage. Immediately, he knew the transmission was blown, the interior was a complete mess, the body was far from being straight or whole, and the firewall was practically rusted through. Once it was stripped down to the frame, Gabe made plans to build a 327-cid Chevy engine all by himself. While gathering some information on the procedure, his brother offered to completely build it as a contribution to the project. Even though Gabe wanted to build the truck by himself, Simon persisted and convinced Gabe to bring out the engine so he could help.
Photo 6/12   |   1983 Chevrolet C10 bed Tubs
After the motor was finished, the next thing on the list was to get the body and frame cleaned and ready to sit on the ground over a set of 22-inch wheels. This involved raising the front crossmember up 2 inches and making new motor mounts and a new transmission crossmember. When it came time to build a step notch in the rear, Gabe had Bill Carlton of Ekstensive Metalworks perform this feat while keeping the frame straight. With the frame set, Gabe installed an airbag suspension and painted everything black. When he got to the body, he figured the old front clip had too much damage and needed to be updated to a version from the '85 model. With the front clip off, Gabe was able to fix the firewall by cutting new pieces of sheetmetal to match and shave. Then, it was shipped over to Kustom Werx to get blocked straight and painted PPG Scarlet Red.
After the paintwork was completed, the truck was taken back to Gabe's garage for the finish work. This included getting the factory bench seat and dash upholstered, as well as replacing all of the other interior pieces. After a few minor finishing parts were added, Gabe's truck was done, to say the least. Having the ability to wrench on trucks, his only obstacle was time. Since Gabe has a non-truck-related job, he was forced to work during his nights and weekends. While he spent many hours in the garage, his two kids were there to help him through every step along the way. We have no doubt that Gabe's kids have gained the skills to customize, as well.
The 411

Gabe Sandoval / Kingwood, Texas
'83 Chevy C10
Photo 7/12   |   1983 Chevrolet C10 engine Compartment
'71 327-cid Chevy motor, bored 0.030 over with 12.5:1 compression / vintage steel crankshaft from a '64 Corvette drag car / JE forged pistons with dome tops / Scat H-Beam rods / ported and polished camel-hump heads / Crane Cams 0.500-plus lift solid roller camshaft / Crane Cams roller rocker arms / ARP bolts / 2-inch billet cog pulley system / chromed alternator / Billet Specialties valve covers and wire looms / MSD 6AL ignition / ACCEL HEI distributor / MSD Super Conductor plug wires / ACCEL spark plugs / Painless wiring harness / Optima YellowTop battery / Edelbrock Performer RPM Air-Gap intake manifold / Holley 750-cfm double-pumper carburetor, Blue fuel pump, fuel regulator, and air cleaner / 1/2-inch stainless fuel lines with Earl's 1/2-inch AN fittings / 150-shot NOS nitrous oxide system / AFCO aluminum radiator with dual electric fans / CSR throttle cable brackets / Hedman shorty headers / dual Flowmaster two-chamber mufflers / Chevy three-speed turbo 350 / B&M 3,600-stall torque converter / B&M Shift Improver Kit / Hurst ratchet shifter / Chevy 10-bolt rearend with 3.73:1 gears
By: Simon Sandoval of Performance Automotive in Laredo, Texas
Photo 8/12   |   1983 Chevrolet C10 rear Passengers Side View
Front: 22x8.5-inch Intro Rally, with 4-1/2-inch backspacing
Rear: 22x10-inch Intro Rally, with 6-inch backspacing
Front: 265/35R22 Sumitomo HTR Sport H/P
Rear: 285/35R22 Sumitomo HTR Sport H/P
Front: DJM upper control arms / Belltech 2-inch drop spindles / Firestone 224C airbags / Gabriel shocks
Rear: Ekstensive Metalworks two-link with Panhard bar / Firestone 224C airbags / Gabriel shocks
Accessories: JAZ 16-gallon fuel cell / Harwood Pinto rack-and-pinion steering setup / GC 450-series valves / two Viair 380 compressors / 1/2-inch stainless steel hard lines / 7-gallon air tank
Chassis: Original frame cleaned and painted black / front crossmember notched and raised 2 inches / custom motor mounts / custom transmission crossmember / Ekstensive Metalworks step-notch in rear
By: Gabe Sandoval / Bill Carlton of Ekstensive Metalworks in Houston, Texas
Body Mods:
Shaved firewall, corner markers, door handles, key holes, driprails, cab seams, wipers, stake pockets, and factory emblems / Grant Kustoms tailgate and roll pan rear combo kit / '85 Chevy front clip / A-Affordable bedliner
By: Kustom Werx of Conroe, Texas
Custom Paint:
PPG Scarlet Red
By: Kustom Werx
Photo 9/12   |   1983 Chevrolet C10 steering Wheel
Original bench seat upholstered in cloth and vinyl / original dash covered in vinyl with glove compartment and ashtray shaved / reproduction door panels with matching vinyl inserts / reproduction carpet kit / Auto Meter Ultra-Lite gauges / Billet Accessories Direct steering wheel and dash inserts / painted steering column
By: Gabe Sandoval / (upholstery) PC Auto Upholstery in Spring, Texas
Kenwood KDC-X879 head unit / 5-1/4-inch coax MB Quart speakers in dash
By: Gabe Sandoval
Special Thanks:
A very special thanks to his wife, Dina, children, Taryn and Kendall, for getting dirty in the garage, Simon Sandoval of Performance Automotive for building such a killer motor, Cory Scott of Kustom Werx for the paint and body, and thanks to Trey, Mike, and Bill for help and efforts.



Subscribe Today and Save up to 83%!

Subscribe Truck Trend Magazine

Subscribe to:

Truck Trend

Subscribe Diesel Power Magazine

Subscribe to:

Diesel Power

Subscribe Truckin Magazine

Subscribe to: