Subscribe to the Free
  • |
  • |
  • From Scratch: 2012 Ford F-150 Lariat 4x4 EcoBoost

From Scratch: 2012 Ford F-150 Lariat 4x4 EcoBoost

Pre-arrival: What It Took to Build Our Long Term F-150 EcoBoost

Allyson Harwood
Jun 8, 2012
Photographers: David Freers
Have you ever wondered what it takes to build a truck? So did we. We followed along as our new long-term truck, a 2012 F-150 Lariat 4x4 EcoBoost, was assembled at Ford's Dearborn Truck Plant. The facility is loaded with Ford history. It's part of the Rouge Complex, and the company built cars at the Dearborn plant from the 1920s (the Model A) until 2004, when its last car, a Mustang, rolled off the line. The building was closed and demolished and production shifted elsewhere on the campus. The Dearborn Truck Plant, also in the Rouge Complex, opened in 2004, and the majority of F-150s are built there.
At The all-new Dearborn Truck Plant, Ford can build up to nine models from three platforms.
Photo 2/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost Front Grill
Since the plant was built from the ground up, the company was able to reduce the number of workstations, improve workflow, and reduce costs and the amount of time it takes to build each vehicle.
The plant also holds a Guinness World Record: It has a 10.4-acre living roof, the largest one in existence, made of drought-resistant groundcover that can absorb carbon dioxide (reducing emissions), plus 4 million gallons of rainwater each year, as part of the plant's storm-water management system. It produces oxygen and provides natural insulation overhead, reducing energy costs. It's expected to last twice as long as a regular roof.
Photo 3/43   |   Ford Dearborn Truck Plant 02
Under this green roof, Ford built more than 344,000 F-150s in 2011, and is on pace to beat that number in 2012. Among the 2012 tally is the truck you see here. From start to finish, save for the final checklist, it takes 18-19 hours to build a single truck. We followed along, catching up with our new long-termer after the stampings were welded together and the truck was painted.

1. The truck's body, bed, roof, and floorpan are welded in place. All the exterior panels, including the doors and hood, are painted at the same time. The cab and box are separated and arrive at the final part of the line at different times. The doors are then removed and components are added on a separate assembly line. Later in the process, the same cab and bed are reunited with the frame and the doors are reinstalled.
Photo 7/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 01

2. The hood receives a layer of sound-deadening material early in the build process.
Photo 8/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 02

3. This is a shot of the bare floorpan and firewall.
Photo 9/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 03

4. Wiring harnesses are put into place early on. As you can see, there are quite a few of them.
Photo 10/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 04

5. Next along the line is the installation of the Cooling Module Assembly. This step includes the radiator, oil cooler, air-conditioning condenser, and wiring for the engine compartment.
Photo 11/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 05

6. Our truck has a moonroof, which goes into place at this point, sliding in through the space where the windshield will go later.

7. The pedal assembly is installed next, along with some of the structure that will end up behind the center console and steering wheel.
Photo 15/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 07

8. The headliner goes on. As with the moonroof, this step is much easier because the windshield isn't in the way.

9. In go the instrument panel and the steering wheel.

10. The frame has been in a separate part of the plant. It comes in from a rail car, and is loaded into the building upside down for easier installation of axles and suspension. Once these components are bolted in, the frame is turned right side up and the brakes are put on.
Photo 22/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 10

11. The engine (an EcoBoost in this case), driveshaft, transmission, exhaust, and fans are brought down from an upper floor at the plant and put in place.
Photo 23/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 11

12. After the bed sides have been preheated in preparation, all the badges and decals are added to the bed.

13. The bed and cab were divorced early in the assembly, but in what Ford calls the marriage cell, they are reunited.

14. The wheels and tires are mounted to the frame, making this a rolling chassis, and the complete body is lowered onto it.
Photo 29/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 14

15. The seats are installed next, followed by the battery.

16. The doors have been traveling alongside the F-150's cab during the assembly process. They are now bolted onto the body.

17. Here, the windshield washer and radiator fluid are added, the air-conditioner is charged, and the F-150 is driven off the line.
Photo 36/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 17

18. After passing through 4.2 miles of the plant's conveyor system, passing hundreds of robots and thousands of employees, this pickup truck is complete. It still is required to go through a detailed checklist and inspection. After that last detail, we finally get to drive it.
Photo 37/43   |   2012 Ford F 150 Lariat 4x4 EcoBoost 18

OFF YOU GO -- Our completed F-150 has just exited the line. In background, the statue of Henry Ford seems to be saying goodbye.



Subscribe Today and Save up to 83%!

Subscribe Truck Trend Magazine

Subscribe to:

Truck Trend

Subscribe Diesel Power Magazine

Subscribe to:

Diesel Power

Subscribe Truckin Magazine

Subscribe to: