Due to the EU’s Global Data Protection Regulation, our website is currently unavailable to visitors from most European countries. We apologize for this inconvenience and encourage you to visit www.motortrend.com for the latest on new cars, car reviews and news, concept cars and auto show coverage, awards and much more.MOTORTREND.COM
Revitalizing a Workhorse With Fabtech Motorsports, Fuel Offroad and Falken Tires Photo Gallery
Bryan Fross –
Jan 24, 2019
Photo 1/43 | HD Uplift 01
Photo 2/43 | HD Uplift 00 | Before
Photo 3/43 | HD Uplift 01 | After
Photo 4/43 | HD Uplift 02 | Fabtech’s 4-inch Performance System with Stealth Shocks (K1121M) includes drop-down brackets, a skidplate, steering knuckles, torsion bar drop brackets, and a block kit for the rear. It’s a simple but effective kit to level out these HDs and get some appropriate-sized tires under them.
Photo 5/43 | HD Uplift 03 | With our ’16 Chevy HD two-wheel drive on the lift, we began our installation by removing the wheels then disassembling the factory suspension.
Photo 6/43 | HD Uplift 04 | For this install, and any GM HD trucks, a torsion bar removal tool is necessary due to the bars being under load when installed.
Photo 7/43 | HD Uplift 05 | After locating the torsion bar cams and threaded bolts, the exposed threads of the torsion bar adjusting bolts were measured and marked for reinstallation.
Photo 8/43 | HD Uplift 06 | The sway bar link ends were removed from the sway bar and lower control arm along with the tie rods.
Photo 9/43 | HD Uplift 07 | The skidplate and splash shield were removed next.
Photo 10/43 | HD Uplift 08 | We carefully removed the brake hose bracket, caliper, rotor, and the wheel speed sensor from the hub and control arm.
Photo 11/43 | HD Uplift 09 | After loosening the upper and lower ball joint nuts, we disconnected them from the steering knuckle and then removed the factory shocks. The shocks were tossed, but the hardware is saved for later.
Photo 12/43 | HD Uplift 10 | We then removed the lower control arms from the frame. We set aside the arms and hardware for reinstallation.
Photo 13/43 | HD Uplift 11 | The front crossmember was removed and the truck is nearly ready for its new suspension.
Photo 14/43 | HD Uplift 12 | To make room for the new crossmember, the old mounts are marked according to the detailed instructions and then cut out on both sides.
Photo 15/43 | HD Uplift 13 | The new crossmember was hoisted into place, bolted in, and left loose for now while the rest of the suspension is assembled.
Photo 16/43 | HD Uplift 14 | Our new Fabtech skidplate is bolted into its new home between the crossmembers.
Photo 17/43 | HD Uplift 15 | We moved on to the lower control arms by fitting both the front and rear bumpstop brackets into place, marking the location, and drilling the necessary holes.
Photo 18/43 | HD Uplift 16 | Then, both brackets were bolted into place, making the arms ready to go back onto the Chevy.
Photo 19/43 | HD Uplift 17 | Our newly modified lower control arms were slid into position and loosely mounted to the new crossmember.
Photo 20/43 | HD Uplift 18 | We removed the factory spindles from the rest of the hub assembly and tossed them aside for the new, beefier, Fabtech replacements.
Photo 21/43 | HD Uplift 19 | The new Fabtech spindles were then mounted to the hub with the hardware from the factory.
Photo 22/43 | HD Uplift 20 | With the spindle mounted to the hub and the entire piece bolted back onto the control arms, we torqued the upper ball joints to 45 ft-lb and the lower ball joints to 70 ft-lb.
Photo 23/43 | HD Uplift 21 | After the spindles were reconnected to the front end, the rest of the factory parts and hardware began to go back on. We reinstalled the tie rods, sway bars, steering components, and brakes.
Photo 24/43 | HD Uplift 22 | The next step was to drop down the factory torsion bar crossmember (shown here). The factory ABS module on the inside of the frame is temporarily moved to access the factory torsion bar key/crossmember bolt.
Photo 25/43 | HD Uplift 23 | Our new torsion bar drop brackets were installed with the long extension arm toward the rear of the truck.
Photo 26/43 | HD Uplift 24 | The crossmember was marked on the backside for the two extension arm holes and then drilled out to ½ inch to fit the new bracket.
Photo 27/43 | HD Uplift 25 | We then slid the torsion bars back into the lower control arms, leaving them forward enough to allow the crossmember enough room to go back into place. Our drop brackets were bolted to the crossmember.
Photo 28/43 | HD Uplift 26 | Our torsion bars and keys were reinstalled into the crossmember.
Photo 29/43 | HD Uplift 27 | The torsion bar tool was used again to hold the bar in place as adjustments were made.
Photo 30/43 | HD Uplift 28 | Here are the Stealth Shocks that come with the Fabtech 4-inch Performance Kit. They feature vehicle-specific valving designed for oversized tires and a 46mm High Flow Piston for the best ride quality.
Photo 31/43 | HD Uplift 29 | Before they could be installed, the shocks were prepared by pressing the eyelet hardware into place.
Photo 32/43 | HD Uplift 30 | We began the front shock installation with the upper shock plate fitted and torqued into the upper shock bucket.
Photo 33/43 | HD Uplift 31 | Our front shocks are fitted into the upper shock plate and mounted in the lower bracket with the supplied hardware.
Photo 34/43 | HD Uplift 32 | With the new spindles, crossmember, skidplate, shocks, and bumpstop brackets installed, the Chevy HD front end was finished.
Photo 35/43 | HD Uplift 33 | Moving to the rear, we start by supporting the rear end then removing the factory U-bolts. The pin hole for the new block was drilled out to ¾ inch to accommodate the new hardware.
Photo 36/43 | HD Uplift 34 | Our new blocks and U-bolts were installed with the small taper toward the front of the vehicle.
Photo 37/43 | HD Uplift 35 | The supplied brackets for the brake lines were then installed on the rear differential.
Photo 38/43 | HD Uplift 36 | We then set the rear shocks into position with the stock bolts, washers, and nuts before tightening to recommended specifications.
Photo 39/43 | HD Uplift 37 | We chose these Monster Lug splined lug nuts to hold our wheel/tire combo in place. They are supplied with the splined socket for easy installation.
Photo 40/43 | HD Uplift 38 | Finally, the 18-inch Fuel Podium Off-Road Wheels and 325/65R18 Falken Wildpeak A/T Tires were bolted up to our Chevy 2500HD.
Photo 41/43 | HD Uplift 39 | The truck was pulled onto the alignment rack then aligned to keep everything straight and make sure the tires keep the correct contact point with the road.
Photo 42/43 | HD Uplift 40 | The black Fuel wheels and 35-inch Falkens were looking great with the white paint and new stance.
Photo 43/43 | HD Uplift 41 | The Fabtech Suspension is simple, clean, and functional as well as being built for long-lasting use on- and off-road.