Exclusive Content
Original Shows, Motorsports and Live Events
Due to the EU’s Global Data Protection Regulation, our website is currently unavailable to visitors from most European countries. We apologize for this inconvenience and encourage you to visit www.motortrend.com for the latest on new cars, car reviews and news, concept cars and auto show coverage, awards and much more.MOTORTREND.COM
  • |
  • |
  • |
  • Get 514hp from your truck’s 6.0L V-8 on 87-octane gas!

Get 514hp from your truck’s 6.0L V-8 on 87-octane gas!

Trick Flow’s LS TrackMax cam adds +71-horsepower and +26 lb-ft

Richard Holdener
Oct 20, 2020
Here is a tip for LS enthusiasts out there: If the question ever arises about how to make an LS better, your go-to response should always be swap the cam! Sure, cylinder heads and intake manifolds are most welcome (especially on cathedral-port applications), but their gains are all but dependent on the presence of wilder-than-stock cam timing. Because the LS was factory fortified with ample displacement, compression, and cylinder head flow (especially anything with rec-port heads like our LY6), they are basically begging for more cam timing. Although a cam upgrade can make significant power gains, there is usually a trade-off inherent in the additional peak power. Cam swaps, especially serious performance grinds, are almost always a case of no free lunch.
The potential for massive top-end power gains exist, but the typical 100-plus-horsepower cam swap often comes with a torque-loss penalty. This is less of a problem on a dedicated race engine, but it definitely must be considered on any kind of daily driver.
For many, the ideal situation is a cam swap that combines plenty of peak power without sacrificing low-end torque. In fact, the mark of a successful cam swap is a grind that offers what we call the "trifecta," which means the cam upgrade does three things: increases the peak power, fattens up the peak torque, and does both with no loss anywhere in the power curve. Achieving one of the elements is easy, combining two gets more difficult, but the trifecta requires selection of just the right cam for the combination. To see if we could manage the trifecta, we set up a test with our 6.0L LY6. For those unfamiliar with the LY6, the 2008 LS motor featured a 4.0-inch bore, 3.622-inch stroke, and was blessed with things like rec-port LS3 heads and even variable valve timing (VVT). For our test, we were only interested in the 6.0L displacement and use of the LS3-style cylinder heads, so we replaced the VVT with a factory LQ9 cam, then added an LS3 intake manifold. What we wound up with was a near-stock 6.0L truck engine that produced peak numbers of 443 hp at 5,400 rpm and 467 lb-ft of torque at 4,500 rpm on the dyno with no parasitic drivetrain losses like engine, transmission, t-case, driveshaft, and axles to sap the numbers.
With our baseline taken care of, it was time for cam selection. Achieving more peak power and more peak torque was not terribly difficult, but doing so without hurting power anywhere else (meaning down at lower engine speeds) was the real trick. In an effort to achieve all three, we selected a TrackMax grind from Trick Flow Specialties (PN: 30602003). This TrackMax cam offers a 0.585/0.585-inch lift split, a 228/230-degree duration split, and 112-degree LSA, which is healthy but below the threshold of what many would consider rowdy race cam territory. Back on the dyno, the peak power output was 514 hp at 5,900 rpm, while peak torque was up to 493 lb-ft at 4,600 rpm. For those keeping score, that's more horsepower and torque than a stock LS7, yet a full liter of displacement less. So far, we had achieved two elements, but only if they came with no loss would we achieve the trifecta. A peek at the power curves revealed that the TrackMax cam had improved the power output through the entire rev range, with gains coming as low as 3,000 rpm. Everyone likes big power and big torque, but you know you have selected the right cam when you hit the trifecta!
On the Dyno:

Stock 6.0L Cam vs. TFS TrackMax

Photo 2/18   |   018 Ly6 Tfs Cam Upgrade 6 0l
The 6.0L LY6 was modified slightly from stock to better represent a typical 6.0L. The VVT cam was replaced by a fixed LQ9 and the LY6 intake was ditched in favor of an LS3 unit (though there is almost no difference between the two intakes). Run with Hooker headers and a 92mm cable-driven throttle-body, the LS3-headed 6.0L produced peak numbers of 443 hp at 5,400 rpm and 467 lb-ft of torque at 4,500 rpm. Torque production exceeded 450 lb-ft for a 1,000-rpm spread; no wonder they used this engine in HD truck applications! After installation of the TFS TrackMax cam, the power output increased to 514 hp at 5,900 rpm and 493 lb-ft of torque at 4,600 rpm. Note that both peak power and torque increased, and that the cam swap improved power through the entire rev range.
Photo 3/18   |   002 Ly6 Tfs Cam Upgrade 6 0l
Although the cam swap can be applied to any stock 6.0L (or any other displacement), our test motor started out life as a 2008 LY6.
Photo 4/18   |   003 Ly6 Tfs Cam Upgrade 6 0l
In addition to the iron block and aluminum rectangular-port LS3 heads, the LY6 also featured variable valve timing (VVT) cam operation. The VVT cam and mechanism was removed prior to our test.
Photo 5/18   |   004 Ly6 Tfs Cam Upgrade 6 0l
In place of the VVT cam, we installed a factory 6.0L LQ9 cam. The specs matched the VVT cam, with the exception of the adjustability.
Photo 6/18   |   005 Ly6 Tfs Cam Upgrade 6 0l
Removal of the VVT cam also required installation of a new front cover. Ours came courtesy of Gandrud Chevrolet.
Photo 7/18   |   006 Ly6 Tfs Cam Upgrade 6 0l
The 2008 LY6 6.0L featured high-flow, rectangular-port LS3 heads (823 castings). With peak flow numbers of 315 cfm, the heads could easily support any power level offered by the cam swap.
Photo 8/18   |   007 Ly6 Tfs Cam Upgrade 6 0l
The factory LS3 (823) heads used on the LY6 truck engine featured LS3-style valve springs. These were more than adequate for the 0.550-lift TFS cam.
Photo 9/18   |   008 Ly6 Tfs Cam Upgrade 6 0l
All testing was run with a set of 1-7/8-inch Hooker long-tube (LS Swap) headers feeding 18-inch collector extensions.
Photo 10/18   |   009 Ly6 Tfs Cam Upgrade 6 0l
 
Although it offered no performance advantage, the factory LY6 truck intake was replaced by a low-profile LS3 intake.
Photo 11/18   |   010 Ly6 Tfs Cam Upgrade 6 0l
The stock LY6 injectors will easily feed the stock engine, but we upgraded to a set of 75-pound/hour injectors to ensure adequate fueling for future mods.
Photo 12/18   |   011 Ly6 Tfs Cam Upgrade 6 0l
Tuning for each cam combo was left to a Holley HP ECU.
Photo 13/18   |   012 Ly6 Tfs Cam Upgrade 6 0l
Run with the production LQ9 cam, the 6.0L produced peak numbers of 443hp at 5,400 rpm and 467 lb-ft of torque at 4,500 rpm.
Photo 14/18   |   013 Ly6 Tfs Cam Upgrade 6 0l
After our baseline run with the stock LQ9 cam, we removed the damper and front cover to allow access to the chain tensioner and cam gear.
Photo 15/18   |   014 Ly6 Tfs Cam Upgrade 6 0l
After removal the cam gear, we turned our attention to the cam retaining plate.
Photo 16/18   |   015 Ly6 Tfs Cam Upgrade 6 0l
Next, we removed the factory LQ9 cam, taking care not to damage the high-mileage cam bearings.
Photo 17/18   |   016 Ly6 Tfs Cam Upgrade 6 0l
Removal of the stock cam allowed installation of the more aggressive TFS TrackMax cam. The TFS cam (PN 30602003) offered 0.585-inch lift (intake and exhaust), a 228/230-degree duration split, and 112-degree LSA.
Photo 18/18   |   017 Ly6 Tfs Cam Upgrade 6 0l
After installation of the TrackMax cam, the power output of the 6.0L LY6 jumped from 443 hp and 467 lb-ft of torque to 514 hp at 5,900 rpm and 493 lb-ft of torque at 4,600 rpm.
 

Sources:

Gandrud Chevrolet
800-242-2844
gandrud.com
Holley/Hooker
270/782-2900
holley.com
Summit Racing
888/939-7497
summitracing.com
Trick Flow Specialties
888/841-6556
Trickflow.com

POPULAR TRUCKS

MOST POPULAR

CLOSE X
BUYER'S GUIDE
SEE THE ALL NEW
NEWS, REVIEWS & SPECS